Johdanto vaiheet ja menetelmät kalibrointi pH mittari
1. Kalibrointi of pH metri/pH metri käytetty sisään laboratoriossa: Milloin kalibrointi yhteinen laboratorio pH mittari instrumentit, instrumentin kaltevuus pitäisi olla säädetty arvoon maksimiin, ja kumi tulppa at yläosa osa elektrodi pitäisi olla vedetty auki altistaa pieni reikä, muuten negatiivinen paine syntyy syntyy aikana kalibrointi, joka johtaa epänormaaliin ionin vaihtoon ratkaisuun ja epätarkka mittaus tiedot.
Ota elektrodi ulos dekantterilasi täytetty kanssa tislattu vesi % 2c ja ime jäännös tislattu vesi päälle elektrodi suodattimen kanssa paperi. Sitten laita elektrodi sisään a dekantterilasi kanssa kanssa sekoitettu fosfori happo allas% % 2c odota enemmän kuin 15 min% 2c ja sitten säädä paikannus nuppi instrumentti instrumentti näyttö 6.% 7b% 7b% 7 dpH% 2c joka on asettaa viite piste instrumentti ensimmäinen. Jälkeen asetus viite piste % 2c ota elektrodi ulos dekantterilasi sisältää sekoitettu fosforihappo happo liuos% 2c pesu elektrodi tislattu vesi tislattu sisään dekantterilasi sisältää tislattu vesi % ja odota noin 3 min liuottaminen jäännös osa sekoitettu fosforihappo happo liuos.
2. Myöhemmin, ota ota elektrodi ulos dekantterilasi täytetty kanssa tislattu vesi % 2c ja ime jäännös tislattu vesi päällä elektrodi kanssa suodatin paperi. sitten laita elektrodi osaksi liuos sisältää kalium vety ftalaatti tai booraksi% 2c odota enemmän kuin 15 min 2c ja tarkkaile onko instrumentti instrumentti näyttää a pH 4.{ % 7 b3% 7 d tai 9.18. Jos ei, säädä kulmakerroin nuppi päällä instrumentti to make instrumentti näyttö 4.00} or 9.18 pH, mikä on yleisesti käytetty kaksipiste korjaus. Jos kolmipiste korjaus on tarvitaan, vain toista toiminto toisesta toisesta ratkaisusta sen mukaan edellä vaiheista. Tämä on kalibrointi menetelmä of happamuus mittari.
3. After calibration, plug the rubber plug back. If it is not used for a while, remember to put saturated solution in the protective sleeve of the electrode to keep the electrode moist, which can prolong the life of the electrode and reduce the asymmetric potential of the electrode. Electrodes have a service life and are fragile. Therefore, each laboratory needs to replace electrodes frequently. Don't think that electrodes will not be replaced if they are not broken during use.
4. Before using the composite electrode, first check whether the glass bulb is cracked or broken. If not, when two-point calibration is carried out with pH buffer solution, the positioning and slope knobs can be adjusted to the corresponding pH value, which is generally considered to be usable. Otherwise, the electrode can be activated according to the instruction manual. The activation method is to soak in 4 percent hydrogen fluoride solution for about 3 ~ 5 s, take it out and rinse it with distilled water; Then soak it in 0.1 mol/L hydrochloric acid solution for several hours, rinse it with distilled water, and then calibrate it. For the non-closed composite electrode, if the internal solution is less than 1/3, an external reference solution, namely 3mol/L potassium fluoride solution, should be added. If the potassium fluoride solution exceeds the position of the small hole, throw off the excess potassium fluoride solution and check whether there are bubbles in the solution. If there are bubbles, flick the electrode to drive them out completely, so as to avoid inaccurate measurement data.
5, kynä PH metri kalibrointi menetelmä:
Immerse the electrode of the test pen in the mixed phosphate standard buffer with pH value of 6.86 (at 25 degree ) and gently shake it; Adjust the calibration potentiometer with a small screwdriver until the displayed value is consistent with the PH value of the standard buffer solution at ambient temperature; The electrode is inserted into the standard buffer solution of potassium hydrogen phthalate with pH4.01 or borax with pH9.18; The displayed value should be within the allowable error range compared with the pH value of the buffer solution.
